Ardo All Error Codes List
Each failure corresponds to a combination of numbers and letters that appear on the screen. Of course, an error code is not a panacea and cannot always show exactly which part is faulty. In most cases, it indicates the direction at which point in the device the diagnosis should begin.
There are not very many such codes in Ardo, due to the fact that the control module of these models is not as complex as, for example, in Bosch. I would like to note that earlier models of washing machines are not equipped with a display, and here it is more problematic to understand the cause of the breakdown. You can understand why the equipment does not function correctly in the table below.
Ardo Washing Machine Error Codes
There may be a leak on the motor contacts. Inspect the device for water leaks and correct the defect. It happens that a foreign object gets into the drum, as a result of which it jams and the engine is unable to turn it.
Another cause of failure may be abrasion of the motor brushes. It is necessary to contact a specialist to replace failed parts.
The most common cause of breakdowns is
- violation of operating technique
- incorrect connection and installation of the device
- unfavorable environmental conditions
- A foreign object has entered the tank and is preventing the drum from rotating;
- Wear of the engine or its elements (brushes, starter winding, tachometer);
- The electronic module has failed
- Bearings and seals are worn out;
- Drive belt is deformed
|
E00 E01 |
The problem is in the drainage system - water does not leave the tank | It is possible to fix the breakdown by cleaning the drain strainer. Also wash the pipes and drain hoses. Often dirt also accumulates under the pump impeller. Review these details. |
| E02 | The problem is in the drainage system - spinning and rinsing are not working properly | Inspect the drain hose. It may be pressed down or positioned incorrectly. It should be located at a distance of 50-60 cm from the floor. If connected to a sewer pipe or to a drain point below 50 centimeters, automatic drainage will occur continuously. |
| E03 | The problem is in the drainage tract system - the time provided for pumping out water exceeds 3 minutes |
Technical malfunction. Unscrew, inspect and wash the drain filter, and install it in place. Inspect the drain pump for serviceability. |
| F2 | Problems with the water heating system | In order to find out why the washing machine does not heat the water, you should check all the wiring that goes from the control controller to the heating element. Assess the serviceability of temperature sensors and heating element contacts. |
| F4 | Bleeding pump malfunction | A common cause of this code is a pump failure. It requires diagnostics and, possibly, subsequent replacement. |
| F5 | Simultaneous operation of draining and filling - the tank of the machine cannot be filled to the required level | Check the correct connection of the elements of the drain system and the triac on the control module, which is responsible for the outlet valve. |
| F6 | Washing machine motor malfunction - drum does not spin |
There may be a leak on the motor contacts. Inspect the device for water leaks and correct the defect. It happens that a foreign object gets into the drum, as a result of which it jams and the engine is unable to turn it.
Another cause of failure may be abrasion of the motor brushes. It is necessary to contact a specialist to replace failed parts. |
| F8 | Exceeding the water level in the tank | The culprit for such a breakdown is often a faulty fill valve or water level sensor. As practice shows, installation of new elements will be required. |
| F9 | Washing machine motor malfunction - drum does not spin |
There may be a leak on the motor contacts. Inspect the device for water leaks and correct the defect. It happens that a foreign object gets into the drum, as a result of which it jams and the engine is unable to turn it.
Another cause of failure may be abrasion of the motor brushes. It is necessary to contact a specialist to replace failed parts. |
| F12 | Washing machine motor malfunction - drum does not spin |
There may be a leak on the motor contacts. Inspect the device for water leaks and correct the defect. It happens that a foreign object gets into the drum, as a result of which it jams and the engine is unable to turn it.
Another cause of failure may be abrasion of the motor brushes. It is necessary to contact a specialist to replace failed parts. |
| F13 | Malfunction of the washing machine control system - programs do not start, the machine does not turn on or stops functioning in the specified program mode | In this situation, contact the workshop. You will need to change the programmer or reflash it. |
| F14 | Malfunction of the washing machine control system - programs do not start, the machine does not turn on or stops functioning in the specified program mode | In this situation, contact the workshop. You will need to change the programmer or reflash it. |
Ardo Dishwasher Error Codes
| E1 * * * * * | Water leak |
| E2 * * * * * | Heating element error |
| E3 * * * * * | Heating error (only shown in test) |
| E4 * * * * * | Water inlet problems |
| E5 * * * * * | Water drainage problems |
| E6 * * * * * | Overflow of water |
Ardo Refrigerator Error Codes
| F1 | Thermostat malfunction |
| F2 | Malfunction of the temperature sensor |
| F3 | Fan operation error |
| F4 | Fan operation error |
| F5 | Water accumulation in the system |
| F6 | Malfunction in the functioning of the electronic module |
| F9 | Malfunction in the functioning of the electronic module |
| F12 | Malfunction in the functioning of the electronic module |
| F13 | Malfunctions in the operation of the control module |
| F14 | Malfunctions in the operation of the control module |
Edgar Gómez (Sunday, 18 August 2024 23:20)
muy buena pagina